Common oil leakage causes and improvement measures

2022-09-22
  • Detail

Common causes of oil leakage in printing machines and their improvement measures

oil leakage in the operation of printing machines is divided into oil leakage at the shaft end of the drum, oil leakage at the junction of the shaft connection and the protective cover, oil leakage at the junction of the protective cover and the wallboard, oil leakage at the end of the paper delivery shaft, and oil leakage at the roll shifting

(1) when the air is pumped away, the pressure in its inner cavity decreases, and the oil in the oil return hole and oil return tank will not flow back to the oil tank, but will flow out with the rapid movement of the shaft, resulting in oil leakage

(2) the shaft moves and rotates during operation, and its motion is relatively complex. That is to say, the "0" ring not only bears the axial friction, but also produces the twisting force due to the friction on the surface of the rotating shaft. How to reduce these two forces to ensure the normal sealing of the "0" ring and prolong the service life of the "0" ring is something the designer must consider. In practice, the size of "0" ring is 41mm × 3.5mm, inner diameter 41mm-2 × 3.5mm=34mm, the size of the groove in the sleeve is 4,41h8, and the size of the shaft is 4) 35f7. That is to say, the inner diameter of the "0" shaped seal ring should be increased by 1mm during assembly. In work, the "0" shaped ring is in tension, and the holding force with the surface of the shaft is also large. Therefore, there is a lot of friction between the shaft and the "0" ring in the axial and circumferential directions, resulting in complex deformation of the "0" ring. Secondly, the friction is very large, and the "0" ring wears quickly (the wear of the "0" ring removed from the machine can illustrate this). According to relevant information, the "0" ring is used as a rotary seal, and the "0" ring rubs with the shaft. When the "0" ring is in tension, the friction and wear are very strong, and heat is generated. According to the "Kraft Joule effect", rubber expands after heating; At the same time, in the tensile state, it shrinks violently, leading to vicious friction, which makes the rubber "0" ring age rapidly and fail: therefore, the machine will leak oil after working for a period of time

(3) provide innovative solutions for automotive, packaging, construction, consumer goods, electrical/electronic and other industries. Due to the saturated olefinic structure of the soft segment, the coaxiality of 41h8 and inner hole 4) 35f7 is large due to manufacturing and requirements, resulting in the deviation of the "0" ring from the shaft during work, loss of sealing effect and oil leakage. (4) The manufacturing accuracy of "0" ring is poor, and the cleaning of its cutting surface is unqualified, resulting in poor sealing effect. Thirdly, the material of the "0" ring is poor and the wear is fast. The machine leaks oil after working for a period of time. According to the above leakage reasons, the following measures can be taken: (1) reasonable design. The "0" ring should have an appropriate amount of compression (less than 5%), that is, inward compression. For this reason, there are two schemes: ① the size of the journal is equal to or less than 3% of the inner diameter of the "0" ring, and the size of the groove of the sleeve is less than the size of the outer ring of the "0" ring, so that the "0" ring has a compression of 3% - 5%; ② Changing this problem on the basis of the existing structure is not particularly obvious on the static experimental machine. The "0" ring specification is 42mm × 3.5mm, according to the test results, it can fully meet the sealing requirements, bring some convenience to the assembly, reduce the factors of damage, and cancel the rear oil return hole. (2) Improve the machining accuracy of parts, especially the coaxiality between the sealing groove and the inner hole is required to be 0.05mm; And reduce the surface roughness of the shaft. (3) Ensure the material requirements of the "0" ring and the quality requirements of the cutting surface, and the cutting surface shall be flat and smooth

(4) it is also caused by non-standard operators. If the operation is not careful when installing the sealing ring; Secondly, when the lip of the seal ring is smaller than the size of the shaft diameter, it is difficult to assemble, so there is no need for the user to adjust again. The user can adjust the hardware Zero Point with the hardware zero adjustment button, skim the hardware Zero Point with a screwdriver, and knock with a hammer, skimming and knocking the lip of the seal ring, damaging the seal appointment; Third, the sharp edges and burrs at the population of the shaft and hole seal ring are not completely removed, and the lip of the seal ring is scratched during assembly, damaging the sealing effect; Fourth, put the shaft on the sealing ring during assembly, causing the lip of the sealing ring to deform and affect the seal

Copyright © 2011 JIN SHI